₨ --

There are numerous occupational hazards associated with mining, including exposure to rockdust which can lead to diseases such as silicosis, asbestosis, and pneumoconiosis. Gases in the mine can lead to asphyxiation and could also be ignited. Mining equipment can generate considerable noise, putting workers at risk for hearing loss. Cave-ins, rock falls, and exposure to excess heat are also known hazards. The current NIOSH Recommended Exposure Limit (REL) of noise is 85 dBA with a 3 dBA exchange rate and the MSHA Permissible Exposure Limit (PEL) is 90 dBA with a 5 dBA exchange rate as an 8-hour time-weighted average. NIOSH has found that 25% of noise-exposed workers in Mining, Quarrying, and Oil and Gas Extraction have hearing impairment. The prevalence of hearing loss increased by 1% from 1991 to 2001 within these workers. Noise studies have been conducted in several mining environments. Stageloaders (84-102 dBA), shearers (85-99 dBA), auxiliary fans (84–120 dBA), continuous mining machines (78–109 dBA), and roof bolters (92–103 dBA) represent some of the noisiest equipment in underground coal mines. Dragline oilers, dozer operators, and welders using air arcing were occupations with the highest noise exposures among surface coal miners. Coal mines had the highest hearing loss injury likelihood. Proper ventilation, hearing protection, and spraying equipment with water are important safety practices in mines.

A locomotive or engine is a rail transport vehicle that provides the motive power for a train. If a locomotive is capable of carrying a payload, it is usually rather referred to as a multiple unit, motor coach, railcar or power car; the use of these self-propelled vehicles is increasingly common for passenger trains, but rare for freight. Traditionally, locomotives pulled trains from the front. However, push-pull operation has become common, where the train may have a locomotive (or locomotives) at the front, at the rear, or at each end. Most recently railroads have begun adopting DPU or distributed power. The front may have one or two locomotives followed by a mid train locomotive that is controlled remotely from the lead unit. In 2002, the first 3.6 tonne, 17 kW hydrogen (fuel cell) -powered mining locomotive was demonstrated in Val-d'Or, Quebec. In 2007 the educational mini-hydrail in Kaohsiung, Taiwan went into service. The Railpower GG20B finally is another example of a fuel cell-electric locomotive. Steam-diesel hybrid locomotives can use steam generated from a boiler or diesel to power a piston engine. The Cristiani Compressed Steam System used a diesel engine to power a compressor to drive and recirculate steam produced by a boiler; effectively using steam as the power transmission medium, with the diesel engine being the prime mover.

Special vehicles for mine rail transportation. In order to adapt to the narrow conditions of underground tunnels, the external dimensions are compact. There are trucks, people's vehicles, material trucks, etc. A minecart is a narrow-gauge railway transport vehicle that transports bulk materials such as coal, ore, and waste rock in mines, and generally needs to be pulled by a locomotive or a winch. According to different structures and unloading methods, mining wagons are divided into: fixed mine carts (material carts, flatbed carts), tipping bucket mine carts, single side curved rail side unloading mine carts, bottom (side) unloading mine carts and shuttle mine carts There are 5 categories. A vehicle pulled by a locomotive or winch to transport coal, gangue, equipment, equipment and personnel. Mine cars are mainly used for rail transportation of underground tunnels, shafts and ground in mines. They are the most used and widely used transportation equipment in coal mines. Standard or narrow-gauge railway transport vehicles for transporting bulk materials such as ore, waste rock and coal in mines, generally pulled by locomotives or winches. In addition to mine trucks for transporting bulk materials, mining vehicles also include flatbed trucks and material trucks specially designed for transporting materials; inclined shaft trucks and level lane trucks for people; other special vehicles, such as explosives trucks, water supply trucks, fire fighting trucks car, sanitary car, etc. Trucks for transporting bulk materials on light rails. Transporting bulk building materials on construction sites by manpower, winches or tractors. It is composed of bucket, frame, walking wheel, coupling and other components. The fixed mine truck body is fixedly connected to the frame, and the mine truck must be turned over and unloaded by a dumper. The bucket of the tipping bucket is supported on the overturning rail of the frame, and the bucket can be overturned and unloaded on the overturning rail.